MIJODA52
Passenger
Posts:7
Send Message
 | | 08/18/2008 9:11 AM |
| | This may sound like a silly question but has anybody tried making a straight section of track (brass) out of a curved section by cutting the plastic tie connector strips on the inner rail? I am about 4 sections of straight track short for my layout but I have lots of curved track. | | | |
|
Robert
1st Class Member
Foreman
Posts:121
Send Message
| | 08/18/2008 9:59 AM |
| Sorry I haven't tried it, but I have certainly straightened curved rail by running it "backwards" through my rail bender. I would think that cutting the ties would then allow you to straighten them out.
Robert | | | |
|
noelw
1st Class Member
Rio Linda, Calif. 95673
Foreman
Posts:233
Send Message
| |
kormsen
in the middle of the westparaguayan semi desert
Conductor
Posts:591
Send Message
| | 08/18/2008 11:31 AM |
| i straighten LGB R1 curves with a hammer.
i hold them over a slightly opened benchvice (for the railfoot)that is about 4" broad.
using a small hammer and a flat piece of iron, that fits between rail foot and railhead, i hammer them roughly straight.
using a steel L-angle, that is long enough, i revise, where i need to hit from which side, to make it perfect.
i allways do two pieces of track together. so i can use the two short rails for one straight and the two long rails for another, without cutting.
including the cutting of the sleeper connections it takes about fifteen minutes the pair. | |
 construction site - keep off! | |
|
Jerry Barnes
1st Class Member
Lexington, NE
Engineer
Posts:1132
Send Message
| | 08/18/2008 12:20 PM |
| | Check with your local club, someone could probably loan you a bender, Train-Li would be the best bet. Jerry | |
Life is too short to take seriously. | |
|
pimanjc
1st Class Member
Jim Carter - Wichita, KS
Conductor
Posts:508
Send Message
| |
Les
1st Class Member
Florissant, Missouri
Foreman
Posts:311
Send Message
| | 08/18/2008 3:14 PM |
| Posted By noelw on 08/18/2008 11:06 AM Posted By MIJODA52 on 08/18/2008 9:11 AM
This may sound like a silly question but has anybody tried making a straight section of track (brass) out of a curved section by cutting the plastic tie connector strips on the inner rail? I am about 4 sections of straight track short for my layout but I have lots of curved track. I'm having the same problem to.. Trying to straighten out LGB curves. I cut ties every 3 inch's on both sides but can't get he last 2 inch's straighten out of 15 or so curve tracks.  " border=0> Hope your post helps us..  " border=0>
Has anyone tried clamping the rail--between a couple of pieces of wood if needed--in a 6" bench vise and working the curve out that way? Likely, to get the last out, you'll have to either do a little creative 'nudging' with a block and light hammer, or try bending w. fingers.
If the rail has a 'set' in the curve that won't come out (the last few fractions) insert a suitable wooden shim at the height of the arc and tighten the jaws. You hafta be careful....
Les | | | |
|
lownote
1st Class Member
Arlington VA
Conductor
Posts:650
Send Message
| | 08/18/2008 3:23 PM |
| I used a train-li bender to straighten a bunch of R! curves in my train shed. They came out very close to perfectly straight and since I'm using them to store freight cars, they work perfectly well. I didn't even cut the webs, I just removed the &%$#! LGB joiners. I ended up making about 20 feet of straight track out of a bunch of R1s
The Trail-Li bender is a pretty remarkable piece of gear. | |
Evading the Midas touch of expertise
http://chnm.gmu.edu/courses/magic/westover/ | |
|
nick s.
Posts:0
Send Message
| | 08/18/2008 4:51 PM |
| heres a video it might help..
Nick...
http://www.youtube.com/watch?v=XuJiCC4ZPPc | | | |
|
Dan Pierce
1st Class Member
South Eastern MA, USA
Foreman
Posts:382
Send Message
| | 08/19/2008 4:37 AM |
| I have used the single rail bender and straightened out LGB R1 rails.
I over bent just a little and the brass sprung back to straight.
| | | |
|